We build make-to-print brackets, busbars, NEMA enclosures, and complex assemblies for Industrial Equipment Manufacturers and Growth-Focused OEMs. We are not a job shop for one-off repairs; we are a production partner built to scale your product lines.
Start with short-run stamping and precision fabrication to validate designs and hit launch dates; move seamlessly to progressive die as your market demand grows. One roof handles cutting, forming, welding, finishing, and kitting—lowering your total landed cost and simplifying your supply chain.
Scalable production for server rack brackets, airflow panels, cable trays, and copper busbar stamping. We support infrastructure rollouts with consistent, high-cosmetic finishes for client-facing hardware.
AMR chassis, conveyor brackets, and sensor plates for automation fleets. We bridge the gap between initial fleet pilots (Short-Run) and mass deployment (Progressive Die).
Damper blades, louver frames, valve reeds, and compressor mounting plates. High-repeatability stamping for OEMs requiring strict airflow and sealing tolerances across thousands of units.
Don’t let tight tolerances kill your unit margins. Use the industry-standard guide to optimize your industrial parts for mass production. Design your brackets and enclosures for cost-efficiency before you cut the first blank.
Conveyor and machine brackets, sensor plates, robot/end-of-arm mounts. Consistent holes, edges and flatness so assemblies line up on the first pass.
Doors, panels and subpanels for electrical/controls. Hinge/hasp plates, PEM hardware, louvers and gland plates to print. Built for NEMA 12/4/4X requirements as specified.
Idler/roller brackets, guide-rail brackets, guards and covers. Short-run for line changes; migrate to progressive to take cost out at volume.
Damper blades, louver frames, flanges, valve reeds/shims and compressor plates. Repeatability and finish where sealing and airflow matter.
Fast iterations without over-tooling.
Cut, form and fit panels, doors, chassis and guards.
Repeatability and piece-price efficiency at scale.
Clean seams, PEM fasteners installed to spec.
Industrial finishes without outside delays.
Labeled, packaged and ready for your lin
Fewer handoffs, tighter tolerance stack-ups, shorter lead times and lower total cost.
AS9100 and ISO 9001 certified; ITAR registered. Support for PPAP/FAI, material certs, inspection reports and traceability. If your project involves UL 508A panel builds or NEMA performance targets, we manufacture to your print and coordinate with your integrator.
Our ISO 9001 QMS standardizes how we plan, build and verify parts for industrial OEMs. Corrective action, preventive action, gauge calibration and supplier control are baked in—so your industrial enclosures, brackets and machined/stamped sub-assemblies arrive consistent lot-to-lot. Cleaner launches, fewer surprises, faster approval.
As an ITAR-registered manufacturer, we control export-restricted technical data for defense programs. Access is limited to authorized U.S. persons; drawings and work instructions move through secure, logged workflows. Pair ITAR with AS9100 and you get a documented path for stamped, fabricated and welded parts that must meet defense and government requirements.
Not a certification—but critical proof. We provide PPAP and FAI deliverables when required: control plans, ballooned prints, dimensional results, material and finish certs, capability studies and traceability records. Ideal for transferring prototype/short-run parts into stable progressive die production without re-qualification headaches.
Every production lot gets a unique ID tied to heat numbers, raw-material certs, operator and machine data, inspection results and finishing records. Barcode labels and digital travelers preserve the chain from stamping/forming through welding, hardware install and powder coating—critical for audits, field returns and regulated builds.
We fabricate doors, panels, subpanels and brackets to your print for projects that require NEMA 12/4/4X performance and integration with UL 508A panel shops. We’ll manage material and finish selections (stainless, galvanized, powder coat), hardware insertion and flatness so enclosures assemble cleanly and pass downstream inspections.
Quality manuals, process flow diagrams, control plans, calibration lists and sample inspection reports are available for review. We host virtual or on-site audits and align to your supplier requirements—so bringing in a new industrial metal stamping and fabrication partner is straightforward and fully documented.
AS9100 and ISO 9001 certified; ITAR registered. Support for PPAP/FAI, material certs, inspection reports and traceability. If your project involves UL 508A panel builds or NEMA performance targets, we manufacture to your print and coordinate with your integrator.
Stainless, aluminum, galvanized and carbon steels are standard; copper/brass for power and controls hardware. Powder coat in house; plating and specialty finishes sourced and managed through our quality system.
FAQs
Stamp flat or shallow-draw parts with repeatable holes/slots (brackets, plates, shims). Fabricate panels, doors, subpanels, chassis and guards that need bends, hems, welds or large formats. Many builds mix both, then weld, install hardware and powder-coat under one roof.
Use short-run for prototypes/pilots and fluctuating demand. Migrate to progressive when annual volume and design stability justify tooling ROI and takt. We’ll share a break-even and timeline so you can plan the switch.
Yes—build-to-print for NEMA 12/4/4X with panel-shop integration (hinge/hasp plates, PEM hardware, gland plates, louvers). We manage seams, flatness and finish so UL 508A assembly is straightforward.
Yes—prototype through production for busbars, brackets, DIN-rail mounts and subpanels. We’ll recommend alloy, thickness and finishes (e.g., tin/nickel) to balance conductivity, stiffness and corrosion.
Prototypes: fast turns. Short-run: quick standard windows. Progressive tooling depends on complexity; we quote tool build + first articles together and can bridge with short-run if demand ramps earlier.
Brackets: carbon, galvanized, stainless. Enclosures/panels: CRS, galvanized, stainless, aluminum. Choose stainless or coated galvanized for corrosion, aluminum for weight; powder coat for durability and color control.
Yes—fabricated, welded, hardware installed and powder-coated in house, with kitting/labeling to your BOM so parts land at point-of-use.
Yes—our AS9100 & ISO 9001 system supports FAI/PPAP, ballooned prints, material/finish certs, capability studies and lot traceability; we provide the packet your SQE expects. (We’re also ITAR registered.)
We lock datums and fixtures from blank to final, control bend deductions, heat input and hardware deformation, and account for coating build. In-process checks + final inspection verify critical features before ship.
Yes. We kit, label and pack sub-assemblies so they reach your line ready to bolt—fewer suppliers, fewer SKUs, fewer stoppages.
Yes—U.S. facilities with AS9100/ISO 9001 certification and ITAR registration. We host virtual or on-site audits and provide quality manuals, calibration lists and sample inspection reports.
Brackets & mounts, enclosures & control panels, material-handling hardware, machine guarding, and HVAC/pumps & compressors components—delivered production-ready.
With 4 locations centered around the busiest manufacturing hubs in the U.S., we continue to expand our services while helping you achieve your vision. You can find Dayton Rogers Manufacturing Co. driving precision in metal stamping for agriculture in the following 4 states:
AGRICULTURAL METAL STAMPING NEAR MINNEAPOLIS, MN
8401 West 35W Service Drive
Minneapolis, MN 55449
AGRICULTURAL METAL STAMPING NEAR COLUMBUS, OH
2309 McGaw Road West
Columbus, OH 43207
AGRICULTURAL METAL STAMPING NEAR COLUMBIA, SC
12223 C R Koon Hwy
Newberry, SC 29108
AGRICULTURAL METAL STAMPING NEAR ARLINGTON, TEXAS
1107 Commercial Blvd N Arlington, TX 76001
8401 West 35W Service Drive, Minneapolis, MN 55449-7260 1-800-677-8881
© 2022 Dayton Rogers. All rights reserved
